الدرس 24 · Memory

SRAM

لم يُترجم بعد؛ يُعرض باللغة الإنجليزية

Static RAM keeps each bit in a cell of six transistors: two inverters joined in a loop hold the bit, and two access transistors, opened by a word line, connect it to a pair of bit lines. Watch one cell blown up as it holds, is read and is written, then see a small grid of cells where a row decoder opens one row at a time. Find out why SRAM is fast, needs no refresh, and is still too big to use for all of a computer's memory.

12 دقيقة10 خطوات5 أسئلةIntermediate

شكل 24 · تفاعلي

جارٍ تحميل الرسم…

أو ← →

اختبر نفسك

5 أسئلة سريعة

اختر إجابة لتعرف السبب. تُحفَظ نتيجتك مع تقدّمك.

01How many transistors does one standard SRAM cell use to store one bit?

Four transistors make the two inverters that hold the bit, and two more are the access transistors: six in all.

02What does the word line do?

The word line drives the gates of the access transistors. At 1 the doors open and the cells in that row reach their bit lines; at 0 they are cut off.

03During a read, both bit lines start at 1. The cell holds Q = 1. What happens when the word line opens the doors?

The side holding 0 pulls its bit line down. Here that is Q̄, so BL̄ dips and the sense amplifier reads a 1. The cell keeps its bit.

04A memory array has 4 rows. How many address bits does its row decoder need, and how many word lines does it raise at a time?

n address bits name 2^n rows, so 2 bits cover 4 rows. The decoder raises exactly one word line: the row the address names.

05Why is SRAM used for caches but not for all of a computer's main memory?

SRAM is fast and needs no refresh, but six transistors per bit make it large and costly. DRAM packs a bit into one transistor and one capacitor, so main memory uses DRAM.

المصطلحات الأساسية

المسرد

SRAM (static RAM): Memory that keeps each bit in a loop of two inverters. It holds the bit while powered and needs no refresh.
Inverter: A gate whose output is the opposite of its input. A CMOS inverter uses two transistors.
Cross-coupled inverters: Two inverters each feeding the other's input. The loop holds itself in one of two steady states: a stored bit.
Access transistor: One of the two transistors that act as doors between an SRAM cell's storage nodes and its bit lines.
Word line: The wire along a row that opens the access transistors of every cell in that row.
Bit lines: A pair of wires, BL and BL̄, down a column. Data is read from and written to the cells through them.
Sense amplifier: A circuit that detects which of two bit lines has dropped a little and turns that into a clean 0 or 1.
Row decoder: A circuit that turns an n-bit row address into exactly one raised word line out of 2^n.

تفاصيل إضافية

الملاحظات والمصادر

A 6T SRAM cell is two cross-coupled CMOS inverters (two transistors each) plus two access transistors whose gates are the word line (Weste and Harris, CMOS VLSI Design, section 12.2).
On a read both bit lines are precharged high; the side of the cell that holds 0 slowly discharges its bit line, and a sense amplifier detects the small difference. On a write the driver is strong enough to overpower the cell's weak pull-up transistors.
In an array every cell of a row shares a word line and every cell of a column shares a bit line pair; a decoder turns an n-bit row address into exactly one of 2^n word lines (Harris and Harris, Digital Design and Computer Architecture, section 5.5).
A DRAM cell is one transistor and one capacitor. The charge leaks, so DDR4 DRAM refreshes every row within 64 ms (JEDEC JESD79-4). SRAM needs no refresh but uses six transistors per bit, so it is used for caches and register files (Hennessy and Patterson, section 2.2).
Both SRAM and DRAM are volatile: they lose their data when the power is switched off. Flash memory is the kind that keeps it.

اختبار يتاح بعد الخطوة الأخيرة.